huxi
448 lines
20 KiB
C
448 lines
20 KiB
C
#ifndef _CVP_DMS_H_
|
||
#define _CVP_DMS_H_
|
||
|
||
#include "generic/typedef.h"
|
||
#include "cvp_common.h"
|
||
|
||
/*降噪版本定义*/
|
||
#define DMS_V100 0xA1
|
||
#define DMS_V200 0xA2
|
||
|
||
//dms_cfg:
|
||
typedef struct {
|
||
u8 mic_again; //DAC增益,default:3(0~14)
|
||
u8 dac_again; //MIC增益,default:22(0~31)
|
||
u8 enable_module; //使能模块
|
||
u8 ul_eq_en; //上行EQ使能,default:enable(disable(0), enable(1))
|
||
/*AGC*/
|
||
float ndt_fade_in; //单端讲话淡入步进default: 1.3f(0.1 ~ 5 dB)
|
||
float ndt_fade_out; //单端讲话淡出步进default: 0.7f(0.1 ~ 5 dB)
|
||
float dt_fade_in; //双端讲话淡入步进default: 1.3f(0.1 ~ 5 dB)
|
||
float dt_fade_out; //双端讲话淡出步进default: 0.7f(0.1 ~ 5 dB)
|
||
float ndt_max_gain; //单端讲话放大上限,default: 12.f(0 ~ 24 dB)
|
||
float ndt_min_gain; //单端讲话放大下限,default: 0.f(-20 ~ 24 dB)
|
||
float ndt_speech_thr; //单端讲话放大阈值,default: -50.f(-70 ~ -40 dB)
|
||
float dt_max_gain; //双端讲话放大上限,default: 12.f(0 ~ 24 dB)
|
||
float dt_min_gain; //双端讲话放大下限,default: 0.f(-20 ~ 24 dB)
|
||
float dt_speech_thr; //双端讲话放大阈值,default: -40.f(-70 ~ -40 dB)
|
||
float echo_present_thr; //单端双端讲话阈值,default:-70.f(-70 ~ -40 dB)
|
||
/*aec*/
|
||
int aec_process_maxfrequency; //default:8000,range[3000:8000]
|
||
int aec_process_minfrequency; //default:0,range[0:1000]
|
||
int af_length; //default:128 range[128:256]
|
||
/*nlp*/
|
||
int nlp_process_maxfrequency; //default:8000,range[3000:8000]
|
||
int nlp_process_minfrequency; //default:0,range[0:1000]
|
||
float overdrive; //default:1,range[0:30]
|
||
/*ans*/
|
||
float aggressfactor; //default:1.25,range[1:2]
|
||
float minsuppress; //default:0.04,range[0.01:0.1]
|
||
float init_noise_lvl; //default:-75dB,range[-100:-30]
|
||
/*enc*/
|
||
int enc_process_maxfreq; //default:8000,range[3000:8000]
|
||
int enc_process_minfreq; //default:0,range[0:1000]
|
||
int sir_maxfreq; //default:3000,range[1000:8000]
|
||
float mic_distance; //default:0.015,range[0.035:0.015]
|
||
float target_signal_degradation;//default:1,range[0:1]
|
||
float enc_aggressfactor; //default:4.f,range[0:4]
|
||
float enc_minsuppress; //default:0.09f,range[0:0.1]
|
||
/*common*/
|
||
float global_minsuppress; //default:0.0,range[0.0:0.09]
|
||
/*回采*/
|
||
u16 adc_ref_en; /*adc回采参考数据使能*/
|
||
/*MFDT Parameters*/
|
||
float detect_time; // // 检测时间s，影响状态切换的速度
|
||
float detect_eng_diff_thr; // 0~-90 dB 两个mic能量差异持续大于此阈值超过检测时间则会检测为故障
|
||
float detect_eng_lowerbound; // 0~-90 dB 当处于故障状态时，正常的mic能量大于此阈值才会检测能量差异，避免安静环境下误判切回正常状态
|
||
int MalfuncDet_MaxFrequency;// 检测信号的最大频率成分
|
||
int MalfuncDet_MinFrequency;// 检测信号的最小频率成分
|
||
int OnlyDetect;// 0 -> 故障切换到单mic模式， 1-> 只检测不切换
|
||
/*debug*/
|
||
u8 output_sel;/*dms output选择*/
|
||
} _GNU_PACKED_ AEC_DMS_CONFIG;
|
||
|
||
//dms_flexible_cfg:
|
||
typedef struct {
|
||
u8 ver; //Ver:01
|
||
u8 mic_again; //MIC0增益,default:10(0~14)
|
||
u8 mic1_again; //MIC1增益,default:3(0~14)
|
||
u8 dac_again; //DAC增益,default:22(0~31)
|
||
u8 enable_module; //使能模块 NS:BIT(2) ENC:BIT(3) AGC:BIT(4)
|
||
u8 ul_eq_en; //上行EQ使能,default:enable(disable(0), enable(1))
|
||
u8 reserved[2];
|
||
|
||
/*AGC*/
|
||
float ndt_fade_in; //单端讲话淡入步进default: 1.3f(0.1 ~ 5 dB)
|
||
float ndt_fade_out; //单端讲话淡出步进default: 0.7f(0.1 ~ 5 dB)
|
||
float dt_fade_in; //双端讲话淡入步进default: 1.3f(0.1 ~ 5 dB)
|
||
float dt_fade_out; //双端讲话淡出步进default: 0.7f(0.1 ~ 5 dB)
|
||
float ndt_max_gain; //单端讲话放大上限,default: 12.f(0 ~ 24 dB)
|
||
float ndt_min_gain; //单端讲话放大下限,default: 0.f(-20 ~ 24 dB)
|
||
float ndt_speech_thr; //单端讲话放大阈值,default: -50.f(-70 ~ -40 dB)
|
||
float dt_max_gain; //双端讲话放大上限,default: 12.f(0 ~ 24 dB)
|
||
float dt_min_gain; //双端讲话放大下限,default: 0.f(-20 ~ 24 dB)
|
||
float dt_speech_thr; //双端讲话放大阈值,default: -40.f(-70 ~ -40 dB)
|
||
float echo_present_thr; //单端双端讲话阈值,default:-70.f(-70 ~ -40 dB)
|
||
/*aec*/
|
||
int aec_process_maxfrequency; //default:8000,range[3000:8000]
|
||
int aec_process_minfrequency; //default:0,range[0:1000]
|
||
int af_length; //default:128 range[128:256]
|
||
/*nlp*/
|
||
int nlp_process_maxfrequency; //default:8000,range[3000:8000]
|
||
int nlp_process_minfrequency; //default:0,range[0:1000]
|
||
float overdrive; //default:1,range[0:30]
|
||
/*ans*/
|
||
float aggressfactor; //default:1.25,range[1:2]
|
||
float minsuppress; //default:0.04,range[0.01:0.1]
|
||
float init_noise_lvl; //default:-75dB,range[-100:-30]
|
||
/*enc*/
|
||
float enc_suppress_pre; //ENC前级压制，越大越强 default:0.6f,range[0:1]
|
||
float enc_suppress_post; //ENC后级压制，越大越强 default:0.15f,range[0:1]
|
||
float enc_minsuppress; //ENC后级压制下限 default:0.09f,range[0:1]
|
||
float enc_disconverge_erle_thr; //滤波器发散控制阈值，越大控制越强 default:-6.f,range[-20:5]
|
||
/*回采*/
|
||
u16 adc_ref_en; /*adc回采参考数据使能*/
|
||
/*debug*/
|
||
u8 output_sel;/*dms output选择*/
|
||
|
||
} _GNU_PACKED_ DMS_FLEXIBLE_CONFIG;
|
||
|
||
typedef struct {
|
||
u8 ver; //Ver:01
|
||
u8 mic_again; //MIC增益,default:3(0~14)
|
||
u8 fb_mic_again; //FB MIC增益,default:3(0~14)
|
||
u8 dac_again; //DAC增益,default:22(0~31)
|
||
u8 enable_module; //使能模块
|
||
u8 ul_eq_en; //上行EQ使能,default:enable(disable(0), enable(1))
|
||
u8 agc_type; //AGC类型选择，0：AGC_EXTERNAL，1：AGC_INTERNAL
|
||
union {
|
||
/*AGC*/
|
||
struct {
|
||
float ndt_fade_in; //单端讲话淡入步进default: 1.3f(0.1 ~ 5 dB)
|
||
float ndt_fade_out; //单端讲话淡出步进default: 0.7f(0.1 ~ 5 dB)
|
||
float dt_fade_in; //双端讲话淡入步进default: 1.3f(0.1 ~ 5 dB)
|
||
float dt_fade_out; //双端讲话淡出步进default: 0.7f(0.1 ~ 5 dB)
|
||
float ndt_max_gain; //单端讲话放大上限,default: 12.f(-90 ~ 40 dB)
|
||
float ndt_min_gain; //单端讲话放大下限,default: 0.f(-90 ~ 40 dB)
|
||
float ndt_speech_thr; //单端讲话放大阈值,default: -50.f(-70 ~ -40 dB)
|
||
float dt_max_gain; //双端讲话放大上限,default: 12.f(-90 ~ 40 dB)
|
||
float dt_min_gain; //双端讲话放大下限,default: 0.f(-90 ~ 40 dB)
|
||
float dt_speech_thr; //双端讲话放大阈值,default: -40.f(-70 ~ -30 dB)
|
||
float echo_present_thr; //单端双端讲话阈值,default:-70.f(-70 ~ -30 dB)
|
||
} agc_ext;
|
||
|
||
/*JLSP AGC*/
|
||
struct {
|
||
int min_mag_db_level;//语音能量放大下限阈值，范围：-90 ~ -35 db，默认-50，单位：dB
|
||
int max_mag_db_level;//语音能量放大上限阈值，范围：-90 ~ 0 dB，默认-3 ，单位dB
|
||
int addition_mag_db_level;//语音补偿能量值，范围：0 ~ 20 dB，默认0 ，单位dB
|
||
int clip_mag_db_level;//语音最大截断能量值，范围：-10 ~ 0 dB，默认-3，单位dB
|
||
int floor_mag_db_level;//语音最小截断能量值，范围：-90 ~ -35 dB，默认-70，单位dB
|
||
} agc_int;
|
||
} agc;
|
||
/*aec*/
|
||
int aec_process_maxfrequency; //default:8000,range[3000:8000]
|
||
int aec_process_minfrequency; //default:0,range[0:1000]
|
||
int af_length; //default:128 range[128:256]
|
||
/*nlp*/
|
||
int nlp_process_maxfrequency; //default:8000,range[3000:8000]
|
||
int nlp_process_minfrequency; //default:0,range[0:1000]
|
||
float overdrive; //default:1,range[0:30]
|
||
/*dns*/
|
||
int dns_process_maxfrequency; //default:8000,range[3000:8000]
|
||
int dns_process_minfrequency; //default:0,range[0:1000]
|
||
float aggressfactor; //default:1.25,range[1:2]
|
||
float minsuppress; //default:0.04,range[0.01:0.1]
|
||
float init_noise_lvl; //default:-75dB,range[-100:-30]
|
||
/*enc*/
|
||
int enc_process_maxfreq; //default:8000,range[3000:8000]
|
||
int enc_process_minfreq; //default:0,range[0:1000]
|
||
float snr_db_T0; //sir设定阈值
|
||
float snr_db_T1; //sir设定阈值
|
||
float floor_noise_db_T;
|
||
float compen_db; //mic增益补偿, dB
|
||
|
||
/*wn*/
|
||
float coh_val_T; //双麦非相关性阈值，范围：0 ~ 1，默认值：0.6
|
||
float eng_db_T; //麦增益能量阈值，范围：0 ~ 255 dB，默认值：80，单位：dB
|
||
|
||
/*回采*/
|
||
u16 adc_ref_en; /*adc回采参考数据使能*/
|
||
/*debug*/
|
||
u8 output_sel;/*dms output选择: 0:Default, 1:Master Raw, 2:Slave Raw, 3:Fbmic Raw*/
|
||
|
||
} _GNU_PACKED_ DMS_HYBRID_CONFIG;
|
||
|
||
typedef struct {
|
||
u8 ver; //Ver:01
|
||
u8 mic_again; //MIC增益,default:3(0~14)
|
||
u8 fb_mic_again; //FB MIC增益,default:3(0~14)
|
||
u8 dac_again; //DAC增益,default:22(0~31)
|
||
u8 enable_module; //使能模块
|
||
u8 ul_eq_en; //上行EQ使能,default:enable(disable(0), enable(1))
|
||
u8 agc_type; //AGC类型选择，0：AGC_EXTERNAL，1：AGC_INTERNAL
|
||
union {
|
||
/*AGC*/
|
||
struct {
|
||
float ndt_fade_in; //单端讲话淡入步进default: 1.3f(0.1 ~ 5 dB)
|
||
float ndt_fade_out; //单端讲话淡出步进default: 0.7f(0.1 ~ 5 dB)
|
||
float dt_fade_in; //双端讲话淡入步进default: 1.3f(0.1 ~ 5 dB)
|
||
float dt_fade_out; //双端讲话淡出步进default: 0.7f(0.1 ~ 5 dB)
|
||
float ndt_max_gain; //单端讲话放大上限,default: 12.f(-90 ~ 40 dB)
|
||
float ndt_min_gain; //单端讲话放大下限,default: 0.f(-90 ~ 40 dB)
|
||
float ndt_speech_thr; //单端讲话放大阈值,default: -50.f(-70 ~ -40 dB)
|
||
float dt_max_gain; //双端讲话放大上限,default: 12.f(-90 ~ 40 dB)
|
||
float dt_min_gain; //双端讲话放大下限,default: 0.f(-90 ~ 40 dB)
|
||
float dt_speech_thr; //双端讲话放大阈值,default: -40.f(-70 ~ -30 dB)
|
||
float echo_present_thr; //单端双端讲话阈值,default:-70.f(-70 ~ -30 dB)
|
||
} agc_ext;
|
||
|
||
/*JLSP AGC*/
|
||
struct {
|
||
int min_mag_db_level;//语音能量放大下限阈值，范围：-90 ~ -35 db，默认-50，单位：dB
|
||
int max_mag_db_level;//语音能量放大上限阈值，范围：-90 ~ 0 dB，默认-3 ，单位dB
|
||
int addition_mag_db_level;//语音补偿能量值，范围：0 ~ 20 dB，默认0 ，单位dB
|
||
int clip_mag_db_level;//语音最大截断能量值，范围：-10 ~ 0 dB，默认-3，单位dB
|
||
int floor_mag_db_level;//语音最小截断能量值，范围：-90 ~ -35 dB，默认-70，单位dB
|
||
} agc_int;
|
||
} agc;
|
||
/*aec*/
|
||
int aec_process_maxfrequency; //default:8000,range[3000:8000]
|
||
int aec_process_minfrequency; //default:0,range[0:1000]
|
||
int af_length; //default:128 range[128:256]
|
||
/*nlp*/
|
||
int nlp_process_maxfrequency; //default:8000,range[3000:8000]
|
||
int nlp_process_minfrequency; //default:0,range[0:1000]
|
||
float overdrive; //default:1,range[0:30]
|
||
/*dns*/
|
||
int dns_process_maxfrequency; //default:8000,range[3000:8000]
|
||
int dns_process_minfrequency; //default:0,range[0:1000]
|
||
float aggressfactor; //default:1.25,range[1:2]
|
||
float minsuppress; //default:0.04,range[0.01:0.1]
|
||
float init_noise_lvl; //default:-75dB,range[-100:-30]
|
||
/*wn*/
|
||
float coh_val_T; //双麦非相关性阈值，范围：0 ~ 1，默认值：0.6
|
||
float eng_db_T; //麦增益能量阈值，范围：0 ~ 255 dB，默认值：80，单位：dB
|
||
|
||
/*回采*/
|
||
u16 adc_ref_en; /*adc回采参考数据使能*/
|
||
/*debug*/
|
||
u8 output_sel;/*dms output选择: 0:Default, 1:Master Raw, 2:Slave Raw, 3:Fbmic Raw*/
|
||
|
||
} _GNU_PACKED_ DMS_AWN_CONFIG;
|
||
|
||
struct dms_attr {
|
||
u8 ul_eq_en: 1;
|
||
u8 wideband: 1;
|
||
u8 wn_en: 1;
|
||
u8 dly_est : 1;
|
||
u8 aptfilt_only: 1;
|
||
u8 reserved: 3;
|
||
|
||
u8 dst_delay;/*延时估计目标延时*/
|
||
u8 EnableBit;
|
||
u8 FB_EnableBit;
|
||
u8 packet_dump;
|
||
u8 SimplexTail;
|
||
u8 output_sel;/*dms output选择*/
|
||
u16 hw_delay_offset;/*dac hardware delay offset*/
|
||
u16 wn_gain;/*white_noise gain*/
|
||
u8 agc_type; /*agc类型*/
|
||
/*AGC*/
|
||
float AGC_NDT_fade_in_step; //in dB
|
||
float AGC_NDT_fade_out_step; //in dB
|
||
float AGC_NDT_max_gain; //in dB
|
||
float AGC_NDT_min_gain; //in dB
|
||
float AGC_NDT_speech_thr; //in dB
|
||
float AGC_DT_fade_in_step; //in dB
|
||
float AGC_DT_fade_out_step; //in dB
|
||
float AGC_DT_max_gain; //in dB
|
||
float AGC_DT_min_gain; //in dB
|
||
float AGC_DT_speech_thr; //in dB
|
||
float AGC_echo_present_thr; //In dB
|
||
int AGC_echo_look_ahead; //in ms
|
||
int AGC_echo_hold; // in ms
|
||
/*AEC*/
|
||
int aec_process_maxfrequency; //default:8000,range[3000:8000]
|
||
int aec_process_minfrequency; //default:0,range[0:1000]
|
||
int af_length; //default:128 range[128:256]
|
||
/*NLP*/
|
||
int nlp_process_maxfrequency; //default:8000,range[3000:8000]
|
||
int nlp_process_minfrequency; //default:0,range[0:1000]
|
||
float overdrive; //default:1,range[0:30]
|
||
/*ANS*/
|
||
float aggressfactor; //default:1.25,range[1:2]
|
||
float minsuppress; //default:0.04,range[0.01:0.1]
|
||
float init_noise_lvl; //default:-75db,range[-100:-30]
|
||
/*ENC*/
|
||
int enc_process_maxfreq; //default:8000,range[3000:8000]
|
||
int enc_process_minfreq; //default:0,range[0:1000]
|
||
int sir_maxfreq; //default:3000,range[1000:8000]
|
||
float mic_distance; //default:0.015,range[0.035:0.015]
|
||
float target_signal_degradation;//default:1,range[0:1]
|
||
float enc_aggressfactor; //default:4.f,range[0:4]
|
||
float enc_minsuppress; //default:0.09f,range[0:0.1]
|
||
/*BCS*/
|
||
int bone_process_maxfreq;
|
||
int bone_process_minfreq;
|
||
float bone_init_noise_lvl;
|
||
int Bone_AEC_Process_MaxFrequency;
|
||
int Bone_AEC_Process_MinFrequency;
|
||
/*common*/
|
||
float global_minsuppress; //default:0.0,range[0.0:0.09]
|
||
/*data handle*/
|
||
int (*cvp_advanced_options)(void *aec,
|
||
void *nlp,
|
||
void *ns,
|
||
void *enc,
|
||
void *agc,
|
||
void *wn,
|
||
void *mfdt);
|
||
int (*aec_probe)(short *mic0, short *mic2, short *mic3, short *ref, u16 len);
|
||
int (*aec_post)(s16 *dat, u16 len);
|
||
int (*aec_update)(u8 EnableBit);
|
||
int (*output_handle)(s16 *dat, u16 len);
|
||
|
||
/*flexible enc*/
|
||
int flexible_af_length; //default:512 range[128、256、512、1024]
|
||
int sir_minfreq; //default:100,range[0:8000]
|
||
int SIR_mean_MaxFrequency; //default:1000,range[0:8000]
|
||
int SIR_mean_MinFrequency; //default:100,range[0:8000]
|
||
float ENC_CoheFlgMax_gamma; //default:0.5f,range[0:1]
|
||
float coheXD_thr; //default:0.5f,range[0:1]
|
||
float Disconverge_ERLE_Thr; //default:-6.f,range[-20:5]
|
||
|
||
/*WN*/
|
||
float wn_detect_time; //in second
|
||
float wn_detect_time_ratio_thr; //0-1
|
||
float wn_detect_thr; //0-1
|
||
float wn_minsuppress; //0-1
|
||
|
||
/*Extended-Parameters*/
|
||
u32 ref_sr;
|
||
u16 ref_channel; /*参考数据声道数*/
|
||
u16 adc_ref_en; /*adc回采参考数据使能*/
|
||
u8 mic_bit_width; /*麦克风数据位宽*/
|
||
u8 ref_bit_width; /*参考数据位宽*/
|
||
|
||
/*DNS Parameters*/
|
||
float DNS_highGain; //EQ强度 range[1.0:3.5]
|
||
float DNS_rbRate; //混响强度 range[0:0.9];
|
||
|
||
/*MFDT Parameters*/
|
||
float detect_time; // // 检测时间s，影响状态切换的速度
|
||
float detect_eng_diff_thr; // 0~-90 dB 两个mic能量差异持续大于此阈值超过检测时间则会检测为故障
|
||
float detect_eng_lowerbound; // 0~-90 dB 当处于故障状态时，正常的mic能量大于此阈值才会检测能量差异，避免安静环境下误判切回正常状态
|
||
int MalfuncDet_MaxFrequency;// 检测信号的最大频率成分
|
||
int MalfuncDet_MinFrequency;// 检测信号的最小频率成分
|
||
int OnlyDetect;// 0 -> 故障切换到单mic模式， 1-> 只检测不切换
|
||
|
||
/*jlsp hybrid enc*/
|
||
float snr_db_T0;
|
||
float snr_db_T1;
|
||
float floor_noise_db_T;
|
||
float compen_db;
|
||
float *transfer_func;
|
||
|
||
/*jlsp hybrid dns*/
|
||
int dns_process_maxfrequency;
|
||
int dns_process_minfrequency;
|
||
|
||
/*jlsp hybrid agc*/
|
||
int min_mag_db_level;
|
||
int max_mag_db_level;
|
||
int addition_mag_db_level;
|
||
int clip_mag_db_level;
|
||
int floor_mag_db_level;
|
||
|
||
/*jlsp dms hybrid wn*/
|
||
float coh_val_T; //双麦非相关性阈值，范围：0 ~ 1，默认值：0.6
|
||
float eng_db_T; //麦增益能量阈值，范围：0 ~ 255 dB，默认值：80，单位：dB
|
||
};
|
||
|
||
s32 aec_dms_init(struct dms_attr *attr);
|
||
s32 aec_dms_exit();
|
||
s32 aec_dms_fill_in_data(void *dat, u16 len);
|
||
int aec_dms_fill_in_ref_data(void *dat, u16 len);
|
||
s32 aec_dms_fill_ref_data(void *data0, void *data1, u16 len);
|
||
void aec_dms_toggle(u8 toggle);
|
||
int aec_dms_cfg_update(AEC_DMS_CONFIG *cfg);
|
||
int aec_dms_reboot(u8 enablebit);
|
||
u8 get_cvp_dms_rebooting();
|
||
|
||
s32 aec_dms_flexible_init(struct dms_attr *attr);
|
||
s32 aec_dms_flexible_exit();
|
||
s32 aec_dms_flexible_fill_in_data(void *dat, u16 len);
|
||
int aec_dms_flexible_fill_in_ref_data(void *dat, u16 len);
|
||
s32 aec_dms_flexible_fill_ref_data(void *data0, void *data1, u16 len);
|
||
void aec_dms_flexible_toggle(u8 toggle);
|
||
int aec_dms_flexible_cfg_update(DMS_FLEXIBLE_CONFIG *cfg);
|
||
int aec_dms_flexible_reboot(u8 enablebit);
|
||
u8 get_cvp_dms_flexible_rebooting();
|
||
|
||
s32 aec_dms_hybrid_init(struct dms_attr *attr);
|
||
s32 aec_dms_hybrid_exit();
|
||
s32 aec_dms_hybrid_fill_in_data(void *dat, u16 len);
|
||
int aec_dms_hybrid_fill_in_ref_data(void *dat, u16 len);
|
||
s32 aec_dms_hybrid_fill_ref_data(void *data0, void *data1, u16 len);
|
||
int cvp_dms_hybrid_read_ref_data(void);
|
||
void aec_dms_hybrid_toggle(u8 toggle);
|
||
int aec_dms_hybrid_cfg_update(DMS_HYBRID_CONFIG *cfg);
|
||
int aec_dms_hybrid_reboot(u8 enablebit);
|
||
u8 get_cvp_dms_hybrid_rebooting();
|
||
|
||
s32 aec_dms_awn_init(struct dms_attr *attr);
|
||
s32 aec_dms_awn_exit();
|
||
s32 aec_dms_awn_fill_in_data(void *dat, u16 len);
|
||
int aec_dms_awn_fill_in_ref_data(void *dat, u16 len);
|
||
s32 aec_dms_awn_fill_ref_data(void *data0, void *data1, u16 len);
|
||
int cvp_dms_awn_read_ref_data(void);
|
||
void aec_dms_awn_toggle(u8 toggle);
|
||
int aec_dms_awn_cfg_update(DMS_AWN_CONFIG *cfg);
|
||
int aec_dms_awn_reboot(u8 enablebit);
|
||
u8 get_cvp_dms_awn_rebooting();
|
||
|
||
/*获取风噪的检测结果，1：有风噪，0：无风噪*/
|
||
int cvp_dms_get_wind_detect_state(void);
|
||
|
||
/*单双麦切换状态
|
||
* 0: 正常双麦 ;
|
||
* 1: 副麦坏了，触发故障
|
||
* -1: 主麦坏了，触发故障
|
||
*/
|
||
int cvp_dms_get_malfunc_state(void);
|
||
|
||
/*
|
||
* 获取mic的能量值，开了MFDT_EN才能用
|
||
* mic: 0 获取主麦能量
|
||
* mic：1 获取副麦能量
|
||
* return：返回能量值，[0~90.3],返回-1表示错误
|
||
*/
|
||
float cvp_dms_get_mic_energy(u8 mic);
|
||
|
||
typedef enum {
|
||
DMS_FLEXIBLE_DUAL_MIC = 0, //双mic
|
||
DMS_FLEXIBLE_USE_TALK_MIC, //通话mic（主麦）
|
||
DMS_FLEXIBLE_USE_REF_MIC, //参考mic（副麦）
|
||
} DMS_FLEXIBLE_MIC;
|
||
|
||
/* 话务耳机切换使用的mic
|
||
* DMS_FLEXIBLE_DUAL_MIC ：正常双麦话务耳机
|
||
* DMS_FLEXIBLE_USE_TALK_MIC ：使用主麦
|
||
* DMS_FLEXIBLE_USE_REF_MIC ：使用副麦
|
||
*/
|
||
int aec_dms_flexible_selete_mic(DMS_FLEXIBLE_MIC mic);
|
||
|
||
int cvp_dms_read_ref_data(void);
|
||
int cvp_dms_flexible_read_ref_data(void);
|
||
|
||
/*
|
||
* 获取风噪检测信息
|
||
* wd_flag: 0 没有风噪，1 有风噪
|
||
* 风噪强度r: 0~BIT(16)
|
||
* wd_lev: 风噪等级，0：弱风，1：中风，2：强风
|
||
* */
|
||
int jlsp_get_wind_detect_info(int *wd_flag, int *wd_val, int *wd_lev);
|
||
|
||
#endif/*_CVP_DMS_H_*/
|